Scrapkit used for this tutorial is
Tiny Turtle Designs ' Sweet Rose' kit
Artwork of ŠAnna Liwanag also
used.. you must purchase her tube
HERE.. and have
a license to use.. Mine is CDO-2339
I made this tutorial using PSP X 6
version. Any version can be used with a few tweaks :)
Supplies (WSL_Mask ,2 animation files and word text art)
#1. Open paper 17.jpg. Shift
+ D to duplicate the window , close the original image.. the copy is
#2. Go to layers/load/save mask/
load mask from disk. Use these settings below.
Merge/ merge group
#3. Image/ Canvas size/ 900 x
900 center justify.
#4. Open rose element 89.png
copy and past it over to your working image.
Use your magic wand tool to select
inside the oval frame. go to Selections/ modify/ expand 10
#5. Open paper 6.jpg resize it 65%
copy and paste it over to your working image.. its layer below the
INVERT the selection and CUT on the
paper layer. Apply a 3D drop shadow on the frame.
#6. Open the tube that's the close
of of the girl. have her layer below the oval frame layer but above
the paper you just
deleted the extra paper on the
Resize the tube her 80% Use your
eraser tool to erase the parts of the tube that you see past the
of the frame.
#7. Set the tubes layer mode to
Luminance (L) Merge down on the tube and its background paper
then merge down
the frame and tube and bkg layer.
Position them as shown below.
#8. Open element 14.png Copy
and paste it over to your working image below the mask layer..
Duplicate the layer.. put one top
left.. one at bottom left.
Resize ALL layers 88%. Go to
image/ canvas size 900 x 900 Center justify.
Below it shows where I turn the top
of element14.png to the right some, so more of the splatters show
#9. Open element 53.png (fan) Use
the deformation tool to turn the fan.. as shown below.
Place it below the frame layer
above the mask layer.
As a general rule when your use the
deformation tool to move or turn an element you need to sharpen
#10. Open element 56.png.. copy and
paste it over to your working image.. go to Image/ free rotate
#11, Open element 69.png (bow)
Open element 86.png resize 50%
Apply a 3D drop shadow on the fan..
using these settings.
all other shadows are in black
#12. Open the Grn&Purpleleaf.png
put a few below the flower layers
#13. Open the main tube your going
to use.. if you use the same one.. notice how her legs are cut off..
which I don't like :) I used the
eraser tool with these settings
and erased the bottom of her legs
where it was flat across
#14. Add a new layer and move to
the bottom of the layer palette.. fill with white.
Open the text art that was in the
supplies zip.... resize 15% copy and paste it over
to your working image...Position
how you'd like it..
You might have some extra white at
the bottom of your image.. you can crop now.
I also resize ALL layers 88%
Right click on the top of your
image...*no need to merge the layers a certain way this time *
#15. Open your animation shop...
Right click in A.S. as a new animation.
Open the two animation files that
were in your supplies zip.
The singlefairy.mng has 20
frames... the smallpinkheartdrop.mng has 28 frames
on your new animation that you
pasted from PSP... duplicate the single frame there till you have
it won't matter that the two mng
files have different amount of frames..
do the smallpinkheartdrop animation
first... Click, hold and drag F:1 of the small pinkheartdrop
. over to F: 1 of your new working
animation from PSP
I place the hearts on top of the
frame on the girls close up picture.
it took me a couple of times of
undoing to get them positioned like I wanted.
Using the single fairy ani next.. I
started on F: 4 of the working animation.. and dropped F:1 of the
single fairy ani over to F: 4 of the working animation.
That way it don't start till after
the hearts start to drop.
Check your animation... see if all
looks ok... if so Save as a GIF...
You should be done :)